QA/Sync/Sync Server Install EL6

Notes for installing Sync Server on Red Hat Enterprise Linux 6 for 64-Bit systems

REF: http://docs.services.mozilla.com/howtos/run-sync.html

General Notes

• The "Building the server" steps can be repeated for each new build you want to test.
• Once it is running, you can point to it for your own Sync server.

• It is highly recommended that Python 2.6.6 be installed before proceeding with the Sync install.
• Python 2.7 appears to be compatible, but the pre-packaged installer assumes 2.6.6.
• Also, it is highly recommended that the developer tools are installed after installing Python 2.6.6.

Installing the Developer Tools

To get a full development environment on the box, do the following:

$ curl -O http://python-distribute.org/distribute_setup.py
$ sudo python2.6 distribute_setup.py
$ sudo easy_install-2.6 MoPyTools

Keeping the build logs

Run the "make build" step as follows:

$ make build 1> buildlog.log 2> builderr.err

Using Sqlite3

If sqlite3 is to be used, the server-full/etc/sync.conf file must be edited to change the default location of the temp.db file. The default location is in /tmp, which will get wiped at each system boot/restart.

Installing Sync Server

Assuming kernal version similar to the following 2.6.32-131.6.1.el6.x86_64 ... x86_64 x86_64 x86_64 GNU/Linux

Pre-Installed Packages

The following packages were already installed by OPs on the sync6 VM:

• Python 2.6.6
• Sqlite3 3.6.20

Required Packages

The following packages need to be installed. This should be a one-off, unless updates/upgrades are needed by the Sync Server code:

• Mercurial
• MySQL Server, Devel, etc.
• Make
• Virtualenv
• SetupTools
• Python virtualenv
• Python devel
• Gcc

Installations

• Install Mercurial 1.4

$ sudo yum install mercurial

• Verify the installation:

$ hg --version

• Install MySQL Server 14.14

$ sudo yum install mysql-server

• Verify the installation:

$ mysql --version

• Install Gnu Make 3.81

$ sudo yum install make

• Verify the installation:

$ make -v

Note: For the more manual installation steps, using /usr/local/src as a working directory, although this can be any location you choose.

• Install SetupTools

$ cd /usr/local/src
$ sudo wget http://pypi.python.org/packages/source/s/setuptools/setuptools-0.6c11.tar.gz
$ sudo tar xzfv setuptools-0.6c11.tar.gz
$ cd setuptools-0.6c11
$ sudo python2.6 setup.py install

• Install Python virtualenv-1.6.4:

$ cd /usr/local/src
$ sudo wget http://pypi.python.org/packages/source/v/virtualenv/virtualenv-1.6.4.tar.gz
$ sudo tar xvfz virtualenv-1.6.4.tar.gz
$ cd virtualenv-1.6.4
$ sudo python2.6 setup.py install

• Install Python Devel for Python 2.6.6

$ sudo yum install python-devel-2.6.6-20.el6.x86_64

• Install GCC, which is required for MySQL-Python

$ cd /usr/local/src
$ sudo yum install gcc

• Verify the installation:

$ which gcc
returns the following
/usr/bin/gcc
$ gcc --version
returns the following
gcc (GCC) 4.4.5 20110214 (Red Hat 4.4.5-6)

• Start up MySQL

sudo /etc/init.d/mysqld start

• Configure MySQL with a password and a test DB for Sync.

mysql -u root -p
There may be no password (or a "blank" password)

• Two commands seems to work to change the password:

mysql> UPDATE mysql.user set Password=PASSWORD('mozroot') WHERE User='root';
mysql> FLUSH PRIVILEGES

• Create a test database for use with SyncServer

mysql> CREATE DATABASE syncdb;
mysql> \quit

Note: mysql-server install usually prints several lines that show how to do initial setup, so those steps could also be followed instead of the listed above.

• Next, clone and build the sync server

Installing to an open folder for now: /opt/sync

$ mkdir /opt/sync
$ cd /opt/sync
$ hg clone https://hg.mozilla.org/services/server-full
$ cd server-full
$ make build

• Install mysql-devel (which is a prereq for MySQL-Python)

$ sudo yum install mysql-devel

• Install MySQL-Python

$ cd /opt/sync/server-full
$ bin/easy_install MySQL-Python

• Configure server-full/etc/sync.conf to use MySQL

Change the two "sqluri" lines to match the following (or similar):
sqluri = mysql://root:mozroot@localhost/syncdb

• Run the following command (see the wiki page) for more information

$ bin/paster serve development.ini

• If the Server is running correctly, you should see something like this

Starting server in PID 3568.
serving on 0.0.0.0:5000 view at http://127.0.0.1:5000

Rebuilding and Deploying the Sync Server

• Kill the Sync Server process

$ kill -9 <PID>

(Leave MySQL running)

• Save the Sync Server directory and its contents

(this in case you want to keep various snapshots)

$ mv server-full server-full-<DATE>

(example: mv server-full server-full-08012011)

• Repeat the build and deploy steps from above
• Make the necessary changes in the server-full/etc/sync.conf file:
• Change the sqluri entries
• Restart the server

For more advanced configurations, including web server support, please see the following documentation:

• http://docs.services.mozilla.com/howtos/run-sync.html

For a more technical overview of Sync Server and an introduction to Mozilla Services, please see the following documentation:

• http://docs.services.mozilla.com